Chassis - Complete & Half
A selection of Richards & Marsland galvanised chassis.
Parts
Complete Marsland Chassis (NRC4642G-M)
The Marsland Defender chassis manufactured by GKN Wheels & Structures, supplied with an insurance accepted GKN Certificate of Authenticity confirming the chassis are constructed using the same materials, processes and quality control techniques as were stipulated at the time of original equipment manufacturer.
Type approved and crash tested.
All Defender chassis are built to 2016 type/latest specification, including rear cross member and A-frame cross member. GKN pressed section main legs/rails made from 2mm steel with 3mm stiffeners fitted and spot welded internally for added strength, effectively giving you 5mm of material where most needed. Chassis supplied with bolt in gearbox cross member, rear cross member to body bracket, A-frame to chassis bushes including fixings. Power steering pipe, fuel filter, fuel tank and fuel line riv nuts fitted to chassis. All holes drilled and tapped excluding rear tow pack holes. Galvanised as standard.
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Galvanising Update
Marsland have changed their post galvanising passivation process. This is due to a new industry-wide regulation that prohibits the use of the chemical TIB Finish CH06, which was previously used to give the chassis a protective coating against water staining.
An upgrade to the passivation tank has been made and an alternative polycoat finish will be used. This new coating still ensures the same high level of durability and protection, but the final product will have a more natural galvanised finish which means, products will no longer have the shiny finish that usually lasts around 12 weeks.
Marsland products will continue to be hot-dip galvanised to the highest standards BS EN ISO 1461, and their longevity will remain unaffected.Half Chassis (DA6670)
Half Chassis (DA6669)
Half Chassis (DA6668)
Half Chassis (DA6648)
Half Chassis (DA2099)
Complete Richards Chassis (DA2057)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately.
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Complete Richards Chassis (DA2057-300TDI)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately.
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Galvanised Bolt-On Crossmember (DA5300)
Bolt-on crossmembers are not supplied with Richards chassis'
Complete Richards Chassis (KVD500730)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Complete Richards Chassis (NRC4356)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately - DA5300
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Complete Richards Chassis (NRC4642G)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately - DA5300
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Quarter Chassis (DA8903)
Complete Richards Chassis (DA2056-300TDI)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Complete Richards Chassis (DA8906)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Complete Richards Chassis (DA8907)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Complete Richards Chassis (DA2056)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Complete Richards Chassis (KVD500710)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately - DA5300
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.Half Chassis (DA2565)
Complete Richards Chassis (DA8901)
All Richards chassis are manufactured in the UK, using locally sourced materials and locally based machine shops. They are located close to the steel city, Sheffield, and therefore optimise the use of local steel, ensuring that all their chassis are formed from 2.5mm British steel which are all galvanised as standard.
All profiling is done 'in house' using their own laser machine, enabling them to have greater control over the quality of parts used and the materials that they are formed from. The chassis are made using 2.5mm side rails which are 25% heavier than the standard 2.0mm rails. Overall this gives a small increase in the vehicle weight but has a massive effect on the long term durability of the chassis.
Bolt on crossmembers are not supplied with Richards chassis but are available separately - DA5300
Important
This is a selection of the chassis that we do. Please enquire if the chassis you require is not listed here.